![picframe for windows desktop picframe for windows desktop](https://windowsradar.com/wp-content/uploads/2021/01/GIMP.jpg)
- #Picframe for windows desktop for free
- #Picframe for windows desktop install
- #Picframe for windows desktop manual
- #Picframe for windows desktop software
Running slideshow.sh from the command-line without an X-session. If you now call “slideshow.sh” from a console in an X-session, feh should run. r - recursively search the target directory for imagesīe sure to change “afranco/Photos/” to your actual image location. # This file is located at /usr/local/bin/slideshow.sh
#Picframe for windows desktop install
Also install the “ unclutter” program to hide the mouse cursor after several seconds of inactivity. Their paths and contents are listed below in the like-named section.Īssuming that you have successfully installed and are running Linux on the laptop, install the “feh” program from .uk. I wrote a few little-tiny bash scripts to call the slideshow and initiallize it. can be run from the command-line without needing a window manager (I’m not sure if this true of other slideshow programs or not).lots and lots of options for delays, sizing, ordering, etc.I chose to use the “feh” image viewer for displaying a slideshow of the photos. You can use any Linux distribution to build your digital pictureframe, but the placement of a few of the initialization scripts may be different on a distribution such as Fedora or SUSE which are not based on Debian (as are Knoppix and Xandros Desktop).
#Picframe for windows desktop manual
A stripped down Debian install would leave more room with less manual cleanup. The big caveat however is that my Xandros installation take up about 1G, half of my laptop’s little 2GB hard drive. The nice thing about Xandros is the good hardware detection, this can make for more painless OS installs if nothing else. Xandros happend to be the distro that was on the machine when I got networking up, so I didn’t bother to change it. I don’t quite remember what the problem was, but I tried Xandros as well as replaced my network card with the above mentioned Xircom one. I had initially tried a Knoppix hard-drive install of “straight” Debian, but had some problems with the network card or something.
![picframe for windows desktop picframe for windows desktop](https://i.pinimg.com/originals/3d/a5/cf/3da5cf7f8aa5c3aeca2b3aec3fa68b86.jpg)
I chose to put Xandros Desktop on my laptop for this project.
#Picframe for windows desktop software
You might as well set up Linux and make sure that all of your hardware and software is working well together before modding the hardware.Its a lot easier to install Linux on a computer with a keyboard and mouse than on a stripped down motherboard/screen packed into a picture frame.This tutorial will start with software for several reasons: When searching around for info on turning a laptop into a digital picture frame, the tutorials I found all focused on modifying the hardware (removing extra plastic, mounting the screen, etc) and made just a passing mention to the software setup involved. All you generally need is an ethernet card that will work with Linux, for the purposes of the picture frame, speed isn’t much of an issue. The one addition I made to my laptop is a Xircom “Cardbus Ethernet 10/100 + Modem 56” PCMCIA ethernet card. Just plug in a PS/2 keyboard and mouse for the install, then access the machine through the network (ssh) after that. To save even more cost, look for ones with broken keyboards/dead batteries, broken touchpad, etc. It turns out that the keyboard works fine in Linux, just not in the MS Windows 95 that had been installed on the machine.Įven if you can’t find one of these for free, they can usually be had for VERY cheap.
#Picframe for windows desktop for free
The laptop I am using for this Linux picture frame project is an old Dell Inspiron 3000 with a Pentium chip that I got for free since the battery had died and the keyboard didn’t work. Using a less resourse-intensive window manager can make these old computers quite usable, even “snappy”. Sidenote: If you wish to use one of these old laptops as a “desktop computer” running Linux, then you would probably be best to use a light-weight window-manager such as ffwm or windowmaker instead of the KDE or Gnome window-managers that come as the defaults in most Linux distrobutions.